请选择 进入手机版 | 继续访问电脑版

GODIY 自己动手亲力亲为的DIY社区一起来吧--GODIY论坛

 找回密码
 注册

扫一扫,访问微社区

搜索
查看: 15200|回复: 4

[TS-XL] BUFFAL NAS全系列TFTP模式刷机教程进入EM及进入后更新固件的安装教程

[复制链接]
发表于 2011-9-27 01:04:06 | 显示全部楼层 |阅读模式
BUFFAL NAS全系列TFTP模式刷机通用教程,教程通用的。



应网友要求写出XL XEL的安装注意,特别注意的地方,小熊用红字标示


特别注意:XEL发现一个小BUG,就是每次关机全报MUP00错误。。只要轻按一下开关。。。就取消了,再开机。。。按下电源键直看到听到(大约五秒)听到嘀嘀两声,网卡灯亮,实际就是开机了,等一会XEL的显示屏就变黄显示了,一年也关不了几次机,自己注意就可以了



这个贴子不写分区的方式,只写怎么进入EM 更新固件注意的地方:

前提:硬盘已分好区

1.设网卡ip为 192.168.11.1 网线直接到NAS最下面的那个网口,比着下图设:

图片1.jpg

2.打开文件夹内的TFTP Boot recovery文件夹,点击TFTP.Boot

图片2.jpg

图片3.jpg


3.运行后,取下NAS上的任何硬盘  按下XL  XEL的电源三秒,听到嘀嘀二声,开机


图片4.jpg


4.务必注意下图TFTP命令行的文件写入回应,注意硬盘灯和网络联接大约要断几次(如网络没有断,看是不是搞错了TFTP的型号,大约三分钟后,面板显示屏,XL应为红色,XEL应是无背光。

图片5.jpg




5.用管理器扫一下,看能不能找到了,如下图显示就是找到了进入EM模式了。
sshot-5.png



  6.XL 直联进入EM模式后,更新固件时必须接路由器,不能直联,务必注意,取下电脑上的网线,修改网卡IP为自动获取,联接到路由器 再刷新管理器,注意看一下,IP变了。

sshot-7.png


7.进入TS-XL和XEL的固件升级程序,两个固件是通用的。点击Updater 点FIND 你如看到如上图的IP如看到不同的IP关了,重点。

sshot-8.png

8.试着点一下UPdate  

sshot-9.png

9.报错了吧。。。下面才是主要的。打开前面板接上分好区的硬盘。XL应变成蓝灯,XEL是没灯显示,但屏全显示press funcsw 131  new disk1  ready 如放在硬盘1的灯 XL为暗红闪,XEL为绿色闪


sshot-10.png


10.过大约10分种,开始自动关机重启了。XL一般会正常启动,可以不理他,XEL特别注意: 第一次重启会红屏显示:system error E00 MPU NO responce  轻按一下电源开关,。。。等10秒钟后系统又黄屏后会重启更新。。启动后会变成蓝屏:F/W   I25 UPdating (这个时间很长)和welcome  to  terastation  过几分钟,系统又会关机重启,又会红屏显示:system error E00 MPU NO responce  按一下电源开关。。。等几秒钟后系统又黄屏后会重启。。显示,NO INIT file at hdd 3  不要理他,等就行了。。。大约2分钟后,屏变蓝显示welcome  to  terastion 会变红后再显示进入了EM模式,你还不要理他,,你还要等。。什么时间,我看到显示版本号TS_XEL  VER.1.54 (代表OK 了)HDD 2错误什么时,,日期显示正常后,拨下网线,换到第二个网口,等一会上面只有网卡灯在亮和硬盘2红灯在亮了。。我们已经成功了。。


11.用管理器找到NAS XEL图标显示?号 XL显示正常,不影响使用。

sshot-2.png

12.点击图标右键打开WEB设置,也可以用上面的IP直接打开。。



sshot-3.png

13 .用户名:admin 密码:password



sshot-4.png


比着说明书,开始享受我们的NAS吧。。
图片6.jpg
图片7.jpg
sshot-1.png
sshot-2.png
sshot-3.png
sshot-4.png
sshot-6.png
sshot-11.png
sshot-12.png
sshot-13.png
发表于 2011-9-27 01:11:46 | 显示全部楼层
终于有了教程~~ 马上开工折腾。
发表于 2011-9-27 02:31:18 | 显示全部楼层
引导:

Sep 26 20:29:28 TS-XL038 linkstation: log saved to NAND(cron)
Sep 26 20:39:43 TS-XL038 u-boot: BUFFALO U-BOOT Start !!!  
Sep 26 20:39:43 TS-XL038 u-boot:  ** LOADER **
Sep 26 20:39:43 TS-XL038 u-boot:  ** BUFFALO BOARD: DB-MV78100-A-BP LE (CFG_ENV_ADDR=fff80000)
Sep 26 20:39:43 TS-XL038 u-boot: U-Boot 1.1.4 (Mar  2 2011 - 09:36:24) Marvell version: 3.3.5
Sep 26 20:39:43 TS-XL038 u-boot: Buffalo Version: 2.09-1.01
Sep 26 20:39:43 TS-XL038 u-boot: U-Boot code: 00600000 -> 0066FFF0  BSS: -> 00684D30
Sep 26 20:39:43 TS-XL038 u-boot: Soc: MV78100 A0 (DDR2)
Sep 26 20:39:43 TS-XL038 u-boot: CPU running @ 800Mhz L2 running @ 266Mhz
Sep 26 20:39:43 TS-XL038 u-boot: SysClock = 400Mhz , TClock = 166Mhz  
Sep 26 20:39:43 TS-XL038 u-boot: DRAM CAS Latency = 5 tRP = 5 tRAS = 19 tRCD=5
Sep 26 20:39:43 TS-XL038 u-boot: DRAM CS[0] base 0x00000000   size 512MB  
Sep 26 20:39:43 TS-XL038 u-boot: DRAM Total size 512MB  64bit width
Sep 26 20:39:43 TS-XL038 u-boot: [512kB@fff80000] Flash: 512 kB
Sep 26 20:39:43 TS-XL038 u-boot: Addresses 8M - 0M are saved for the U-Boot usage.
Sep 26 20:39:43 TS-XL038 u-boot: Mem malloc Initialization (8M - 7M): Done
Sep 26 20:39:43 TS-XL038 u-boot: NAND:512 MB
Sep 26 20:39:43 TS-XL038 u-boot: CPU 0: ARM926 (Rev 0)
Sep 26 20:39:43 TS-XL038 u-boot: Streaming enabled  
Sep 26 20:39:43 TS-XL038 u-boot: Write allocate disabled
Sep 26 20:39:43 TS-XL038 u-boot: FPU initialized to Run Fast Mode.
Sep 26 20:39:43 TS-XL038 u-boot: enaDCPref <NULL>
Sep 26 20:39:43 TS-XL038 u-boot: enaICPref <NULL>
Sep 26 20:39:43 TS-XL038 u-boot: setL2CacheWT no
Sep 26 20:39:43 TS-XL038 u-boot: setL2Size256K no
Sep 26 20:39:43 TS-XL038 u-boot: disL2Ecc no
Sep 26 20:39:43 TS-XL038 u-boot: disL2Prefetch yes
Sep 26 20:39:43 TS-XL038 u-boot: disL2Cache no
Sep 26 20:39:43 TS-XL038 u-boot: env finished
Sep 26 20:39:43 TS-XL038 u-boot: USB 0: host mode
Sep 26 20:39:43 TS-XL038 u-boot: USB 1: host mode
Sep 26 20:39:43 TS-XL038 u-boot: USB 2: host mode
Sep 26 20:39:43 TS-XL038 u-boot: PCI 0: PCI Express Root Complex Interface
Sep 26 20:39:43 TS-XL038 u-boot: PEX interface detected Link X4
Sep 26 20:39:43 TS-XL038 u-boot: PEX 4: interface detected no Link.
Sep 26 20:39:43 TS-XL038 u-boot: Net:   egiga0 [PRIME], egiga1
Sep 26 20:39:43 TS-XL038 u-boot: buffalo_change_power_status > Read 0x18(reboot)
Sep 26 20:39:43 TS-XL038 u-boot: buffalo_change_power_status > Writing 0x5c(swpoff_uboot_passed)
Sep 26 20:39:43 TS-XL038 u-boot: Skip to wake up disk0.(already waken up)
Sep 26 20:39:43 TS-XL038 u-boot: Skip to wake up disk1.(already waken up)
Sep 26 20:39:43 TS-XL038 u-boot: Skip to wake up disk2.(already waken up)
Sep 26 20:39:43 TS-XL038 u-boot: Skip to wake up disk3.(already waken up)
Sep 26 20:39:43 TS-XL038 u-boot: Marvell Serial ATA Adapter
Sep 26 20:39:43 TS-XL038 u-boot: Integrated Sata device found
Sep 26 20:39:43 TS-XL038 u-boot: Found adapter at bus 0, device 1 ... Scanning channels
Sep 26 20:39:43 TS-XL038 u-boot: [1 0 0]: Enable DMA mode
Sep 26 20:39:43 TS-XL038 u-boot:   Device 2 @ 1 0:
Sep 26 20:39:43 TS-XL038 u-boot: Model: ST3160812AS                 41N3268 LEN  Firm: 3.AAK    Ser#:             9LS4V05H
Sep 26 20:39:43 TS-XL038 u-boot:             Type: Hard Disk
Sep 26 20:39:43 TS-XL038 u-boot:             Supports 48-bit addressing
Sep 26 20:39:43 TS-XL038 u-boot:             Capacity: 152627.8 MB = 149.0 GB (312581808 x 512)
Sep 26 20:39:43 TS-XL038 u-boot: [1 1 0]: Enable DMA mode
Sep 26 20:39:43 TS-XL038 u-boot:   Device 3 @ 1 1:
Sep 26 20:39:43 TS-XL038 u-boot: Model: WDC WD2500JS-00NCB1                      Firm: 10.02E02 Ser#:      WD-WCANK7873370
Sep 26 20:39:43 TS-XL038 u-boot:             Type: Hard Disk
Sep 26 20:39:43 TS-XL038 u-boot:             Supports 48-bit addressing
Sep 26 20:39:43 TS-XL038 u-boot:             Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Sep 26 20:39:43 TS-XL038 u-boot: [1 2 0]: Enable DMA mode
Sep 26 20:39:43 TS-XL038 u-boot:   Device 4 @ 1 2:
Sep 26 20:39:43 TS-XL038 u-boot: Model: WDC WD2500JS-00NCB1                      Firm: 10.02E02 Ser#:      WD-WCANK7893611
Sep 26 20:39:43 TS-XL038 u-boot:             Type: Hard Disk
Sep 26 20:39:43 TS-XL038 u-boot:             Supports 48-bit addressing
Sep 26 20:39:43 TS-XL038 u-boot:             Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Sep 26 20:39:43 TS-XL038 u-boot: [1 3 0]: Enable DMA mode
Sep 26 20:39:43 TS-XL038 u-boot:   Device 5 @ 1 3:
Sep 26 20:39:43 TS-XL038 u-boot: Model: Hitachi HDT721010SLA360                  Firm: ST6OA31B Ser#:       STF607MH1N26KW
Sep 26 20:39:43 TS-XL038 u-boot:             Type: Hard Disk
Sep 26 20:39:43 TS-XL038 u-boot:             Supports 48-bit addressing
Sep 26 20:39:43 TS-XL038 u-boot:             Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
Sep 26 20:39:43 TS-XL038 u-boot: MAC Address on eth0  : 00:1d:73:df:30:38
Sep 26 20:39:43 TS-XL038 u-boot: Signature version    : 1.00
Sep 26 20:39:43 TS-XL038 u-boot: Signature MACAddress : 00:1d:73:df:30:38
Sep 26 20:39:43 TS-XL038 u-boot: 2820252 bytes read
Sep 26 20:39:43 TS-XL038 u-boot:    Image Name:   Linux-2.6.31.8-mv78100
Sep 26 20:39:43 TS-XL038 u-boot:    Created:      2011-07-01   9:09:18 UTC
Sep 26 20:39:43 TS-XL038 u-boot:    Image Type:   ARM Linux Kernel Image (uncompressed)
Sep 26 20:39:43 TS-XL038 u-boot:    Data Size:    2820188 Bytes =  2.7 MB
Sep 26 20:39:43 TS-XL038 u-boot:    Load Address: 00008000
Sep 26 20:39:43 TS-XL038 u-boot:    Entry Point:  00008000
Sep 26 20:39:43 TS-XL038 u-boot: 9294432 bytes read
Sep 26 20:39:43 TS-XL038 u-boot:    Image Name:   initrd
Sep 26 20:39:43 TS-XL038 u-boot:    Created:      2011-07-01   9:13:58 UTC
Sep 26 20:39:43 TS-XL038 u-boot:    Image Type:   ARM Linux RAMDisk Image (gzip compressed)
Sep 26 20:39:43 TS-XL038 u-boot:    Data Size:    9294368 Bytes =  8.9 MB
Sep 26 20:39:43 TS-XL038 u-boot:    Load Address: 00000000
Sep 26 20:39:43 TS-XL038 u-boot:    Entry Point:  00000000
Sep 26 20:39:43 TS-XL038 u-boot: Signature version    : 1.00
Sep 26 20:39:43 TS-XL038 u-boot: Signature MACAddress : 00:1d:73:df:30:38
Sep 26 20:39:43 TS-XL038 u-boot: 2820252 bytes read
Sep 26 20:39:43 TS-XL038 u-boot:    Image Name:   Linux-2.6.31.8-mv78100
Sep 26 20:39:43 TS-XL038 u-boot:    Created:      2011-07-01   9:09:18 UTC
Sep 26 20:39:43 TS-XL038 u-boot:    Image Type:   ARM Linux Kernel Image (uncompressed)
Sep 26 20:39:43 TS-XL038 u-boot:    Data Size:    2820188 Bytes =  2.7 MB
Sep 26 20:39:43 TS-XL038 u-boot:    Load Address: 00008000
Sep 26 20:39:43 TS-XL038 u-boot:    Entry Point:  00008000
Sep 26 20:39:43 TS-XL038 u-boot: 9294432 bytes read
Sep 26 20:39:43 TS-XL038 u-boot:    Image Name:   initrd
Sep 26 20:39:43 TS-XL038 u-boot:    Created:      2011-07-01   9:13:58 UTC
Sep 26 20:39:43 TS-XL038 u-boot:    Image Type:   ARM Linux RAMDisk Image (gzip compressed)
Sep 26 20:39:43 TS-XL038 u-boot:    Data Size:    9294368 Bytes =  8.9 MB
Sep 26 20:39:43 TS-XL038 u-boot:    Load Address: 00000000
Sep 26 20:39:43 TS-XL038 u-boot:    Entry Point:  00000000
Sep 26 20:39:43 TS-XL038 u-boot: Signature version    : 1.00
Sep 26 20:39:43 TS-XL038 u-boot: Signature MACAddress : 00:1d:73:df:30:38
Sep 26 20:39:43 TS-XL038 u-boot: 2820252 bytes read
Sep 26 20:39:43 TS-XL038 u-boot:    Image Name:   Linux-2.6.31.8-mv78100
Sep 26 20:39:43 TS-XL038 u-boot:    Created:      2011-07-01   9:09:18 UTC
Sep 26 20:39:43 TS-XL038 u-boot:    Image Type:   ARM Linux Kernel Image (uncompressed)
Sep 26 20:39:43 TS-XL038 u-boot:    Data Size:    2820188 Bytes =  2.7 MB
Sep 26 20:39:43 TS-XL038 u-boot:    Load Address: 00008000
Sep 26 20:39:43 TS-XL038 u-boot:    Entry Point:  00008000
Sep 26 20:39:43 TS-XL038 u-boot: 9294432 bytes read
Sep 26 20:39:43 TS-XL038 u-boot:    Image Name:   initrd
Sep 26 20:39:43 TS-XL038 u-boot:    Created:      2011-07-01   9:13:58 UTC
Sep 26 20:39:43 TS-XL038 u-boot:    Image Type:   ARM Linux RAMDisk Image (gzip compressed)
Sep 26 20:39:43 TS-XL038 u-boot:    Data Size:    9294368 Bytes =  8.9 MB
Sep 26 20:39:43 TS-XL038 u-boot:    Load Address: 00000000
Sep 26 20:39:43 TS-XL038 u-boot:    Entry Point:  00000000
Sep 26 20:39:43 TS-XL038 u-boot: Signature version    : 1.00
Sep 26 20:39:43 TS-XL038 u-boot: Signature MACAddress : 00:1d:73:df:30:38
Sep 26 20:39:43 TS-XL038 u-boot: 2820252 bytes read
Sep 26 20:39:43 TS-XL038 u-boot:    Image Name:   Linux-2.6.31.8-mv78100
Sep 26 20:39:43 TS-XL038 u-boot:    Created:      2011-07-01   9:09:18 UTC
Sep 26 20:39:43 TS-XL038 u-boot:    Image Type:   ARM Linux Kernel Image (uncompressed)
Sep 26 20:39:43 TS-XL038 u-boot:    Data Size:    2820188 Bytes =  2.7 MB
Sep 26 20:39:43 TS-XL038 u-boot:    Load Address: 00008000
Sep 26 20:39:43 TS-XL038 u-boot:    Entry Point:  00008000
Sep 26 20:39:43 TS-XL038 u-boot: 9294432 bytes read
Sep 26 20:39:43 TS-XL038 u-boot:    Image Name:   initrd
Sep 26 20:39:43 TS-XL038 u-boot:    Created:      2011-07-01   9:13:58 UTC
Sep 26 20:39:43 TS-XL038 u-boot:    Image Type:   ARM Linux RAMDisk Image (gzip compressed)
Sep 26 20:39:43 TS-XL038 u-boot:    Data Size:    9294368 Bytes =  8.9 MB
Sep 26 20:39:43 TS-XL038 u-boot:    Load Address: 00000000
Sep 26 20:39:43 TS-XL038 u-boot:    Entry Point:  00000000
Sep 26 20:39:43 TS-XL038 u-boot:  ***** Debug *****
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[0].IsMyDisk = 1
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[0].uImage_date = 1309511358
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[0].initrd_date = 1309511638
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[1].IsMyDisk = 1
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[1].uImage_date = 1309511358
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[1].initrd_date = 1309511638
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[2].IsMyDisk = 1
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[2].uImage_date = 1309511358
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[2].initrd_date = 1309511638
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[3].IsMyDisk = 1
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[3].uImage_date = 1309511358
Sep 26 20:39:43 TS-XL038 u-boot: diskinfo[3].initrd_date = 1309511638
Sep 26 20:39:43 TS-XL038 u-boot: newest_fw_dev is updated to 2
Sep 26 20:39:43 TS-XL038 u-boot: Booting from Device 2  
Sep 26 20:39:43 TS-XL038 u-boot: hit any key to switch tftp boot.
Sep 26 20:39:43 TS-XL038 u-boot: Hit any key to stop autoboot:  2 ^H^H^H 1 ^H^H^H 0  
Sep 26 20:39:43 TS-XL038 u-boot: Hit any key to stop autoboot:  3 ^H^H^H 2 ^H^H^H 1 ^H^H^H 0  
Sep 26 20:39:43 TS-XL038 u-boot: 2820252 bytes read
Sep 26 20:39:43 TS-XL038 u-boot: 9294432 bytes read
Sep 26 20:39:43 TS-XL038 u-boot: <<stop_sound>>
Sep 26 20:39:43 TS-XL038 u-boot: ## Booting image at 02000000 ...
Sep 26 20:39:43 TS-XL038 u-boot:    Image Name:   Linux-2.6.31.8-mv78100
Sep 26 20:39:43 TS-XL038 u-boot:    Created:      2011-07-01   9:09:18 UTC
Sep 26 20:39:43 TS-XL038 u-boot:    Image Type:   ARM Linux Kernel Image (uncompressed)
Sep 26 20:39:43 TS-XL038 u-boot:    Data Size:    2820188 Bytes =  2.7 MB
Sep 26 20:39:43 TS-XL038 u-boot:    Load Address: 00008000
Sep 26 20:39:43 TS-XL038 u-boot:    Entry Point:  00008000
Sep 26 20:39:43 TS-XL038 u-boot:    Verifying Checksum ... OK
Sep 26 20:39:43 TS-XL038 u-boot: OK
Sep 26 20:39:43 TS-XL038 u-boot: call do_bootm_linux
Sep 26 20:39:43 TS-XL038 u-boot: ## Loading Ramdisk Image at 00900000 ...
Sep 26 20:39:43 TS-XL038 u-boot:    Image Name:   initrd
Sep 26 20:39:43 TS-XL038 u-boot:    Created:      2011-07-01   9:13:58 UTC
Sep 26 20:39:43 TS-XL038 u-boot:    Image Type:   ARM Linux RAMDisk Image (gzip compressed)
Sep 26 20:39:43 TS-XL038 u-boot:    Data Size:    9294368 Bytes =  8.9 MB
Sep 26 20:39:43 TS-XL038 u-boot:    Load Address: 00000000
Sep 26 20:39:43 TS-XL038 u-boot:    Entry Point:  00000000
Sep 26 20:39:43 TS-XL038 u-boot:    Verifying Checksum ... OK
Sep 26 20:39:44 TS-XL038 linkstation: Started logchkd
Sep 26 20:39:44 TS-XL038 linkstation: Started inetd
Sep 26 20:39:44 TS-XL038 errormon[1830]: errormon-ver.2.00 started
Sep 26 20:39:44 TS-XL038 linkstation: Started errormon
Sep 26 20:39:44 TS-XL038 linkstation: Started kernelmon
Sep 26 20:39:45 TS-XL038 kernelmon: cmd=SATA 0 plugged
Sep 26 20:39:46 TS-XL038 kernelmon: cmd=SATA 1 plugged
Sep 26 20:39:47 TS-XL038 kernelmon: cmd=SATA 2 plugged
Sep 26 20:39:48 TS-XL038 kernelmon: cmd=SATA 3 plugged
Sep 26 20:39:49 TS-XL038 kernelmon: cmd=lanact 0 full eth0
Sep 26 20:39:49 TS-XL038 kernelmon: cmd=lanact 1000 full eth0
Sep 26 20:39:56 TS-XL038 start_data_array.sh: IS_CHECK_ARRAY_STAUS 0
Sep 26 20:39:56 TS-XL038 start_data_array.sh: *** diskinfo guess ***
Sep 26 20:39:58 TS-XL038 start_data_array.sh:  >check array's mount point
Sep 26 20:39:58 TS-XL038 start_data_array.sh:  >check normal state
Sep 26 20:39:58 TS-XL038 start_data_array.sh:   * The status is normal? *
Sep 26 20:39:58 TS-XL038 start_data_array.sh:    skip normal status checking.
Sep 26 20:39:58 TS-XL038 start_data_array.sh: *** compaire ***
Sep 26 20:39:58 TS-XL038 start_data_array.sh:  array1=off ... [skip]
Sep 26 20:39:58 TS-XL038 start_data_array.sh:  array2=off ... [skip]
Sep 26 20:39:58 TS-XL038 start_data_array.sh:  disk1=normal ... [skip]
Sep 26 20:39:58 TS-XL038 start_data_array.sh:  disk2=normal ... [skip]
Sep 26 20:39:58 TS-XL038 start_data_array.sh:  disk3=normal ... [skip]
Sep 26 20:39:58 TS-XL038 start_data_array.sh:  disk4=normal ... [skip]
Sep 26 20:39:58 TS-XL038 start_data_array.sh: diskinfo ... [OK]
Sep 26 20:40:46 TS-XL038 linkstation: cron.sh : logrotate.status deleted.
Sep 26 20:40:52 TS-XL038 S40B_update_notifications.sh: deleting old settings...
Sep 26 20:40:52 TS-XL038 S40B_update_notifications.sh: checking and registering to cron...
Sep 26 20:40:53 TS-XL038 twonky: Media Server script is begun. type=start
Sep 26 20:40:54 TS-XL038 S40B_update_notifications.sh: starting f/w cheking process ...
Sep 26 20:40:54 TS-XL038 twonky: Media Server begins starting. contentbase=/mnt/disk1/share diskinfo=
Sep 26 20:40:57 TS-XL038 S40B_update_notifications.sh: step1 result=0
Sep 26 20:40:57 TS-XL038 S40B_update_notifications.sh: version_is_latest
Sep 26 20:40:57 TS-XL038 S40B_update_notifications.sh: deleting from lcd...
Sep 26 20:41:01 TS-XL038 splx_buffalo.sh: TMNAS is not supported on this model
Sep 26 20:41:04 TS-XL038 root: linkstation
Sep 26 20:41:05 TS-XL038 twonky: Media Server start was completed. build date=2009-11-09
Sep 26 20:41:08 TS-XL038 hdd_raid_syncspeed.sh: /dev/md0 sync speed max is setted to 50000
Sep 26 20:41:08 TS-XL038 hdd_raid_syncspeed.sh: /dev/md1 sync speed max is setted to 50000
Sep 26 20:41:08 TS-XL038 hdd_raid_syncspeed.sh: /dev/md10 sync speed max is setted to 50000
Sep 26 20:41:10 TS-XL038 linkstation: #[miconapl.mcon_get_version] mcon_version=TS-XL/WL  Ver1.0
Sep 26 20:41:35 TS-XL038 linkstation: 1.54-3.31 2011/07/01 18:11:52 started!
Sep 26 20:41:46 TS-XL038 kernelmon: cmd=PSW_on
Sep 26 20:45:06 TS-XL038 linkstation: log saved to NAND(cron)
Sep 26 21:22:06 TS-XL038 bittorrent: ps :  3177 root       2336 S   /usr/local/bittorrent/bin/btdog /usr/local/bittorrent  3178 root      40508 S   /usr/local/bittorrent/bin/bt   3222 root       2336 S   /usr/local/bittorrent/bin/btdog /usr/local/bittorrent  3223 root      36452 S   /usr/local/bittorrent/bin/bt
Sep 26 21:22:08 TS-XL038 bittorrent: ps :  3178 root      40508 S   /usr/local/bittorrent/bin/bt
Sep 26 21:22:09 TS-XL038 bittorrent: WaitBtDie is finished.
Sep 26 21:22:10 TS-XL038 bittorrent: Folder setting is changed.
Sep 26 21:22:10 TS-XL038 bittorrent: WaitBtDie is finished.
Sep 26 21:22:24 TS-XL038 bittorrent: ps :  9769 root       2336 S   /usr/local/bittorrent/bin/btdog /usr/local/bittorrent  9770 root      36452 S   /usr/local/bittorrent/bin/bt
Sep 26 21:22:25 TS-XL038 bittorrent: ps :  9770 root      36452 S   /usr/local/bittorrent/bin/bt
Sep 26 21:22:26 TS-XL038 bittorrent: WaitBtDie is finished.
Sep 26 21:28:30 TS-XL038 bittorrent: ps : 10035 root       2336 S   /usr/local/bittorrent/bin/btdog /usr/local/bittorrent 10036 root      36452 S   /usr/local/bittorrent/bin/bt
Sep 26 21:28:31 TS-XL038 bittorrent: WaitBtDie is finished.
Sep 26 21:28:32 TS-XL038 bittorrent: Folder setting is changed.
Sep 26 21:28:32 TS-XL038 bittorrent: WaitBtDie is finished.
Sep 26 21:33:09 TS-XL038 bittorrent: ps : 16119 root       2336 S   /usr/local/bittorrent/bin/btdog /usr/local/bittorrent 16120 root      36508 S   /usr/local/bittorrent/bin/bt
Sep 26 21:33:10 TS-XL038 bittorrent: WaitBtDie is finished.
Sep 26 21:42:30 TS-XL038 bittorrent: WaitBtDie is finished.
Sep 26 21:42:31 TS-XL038 bittorrent: Folder setting is changed.
Sep 26 21:42:31 TS-XL038 bittorrent: WaitBtDie is finished.
Sep 26 23:26:13 TS-XL038 twonky: Media Server script is begun. type=stop
Sep 26 23:26:16 TS-XL038 twonky: stop Media Server
Sep 26 23:26:21 TS-XL038 bittorrent: ps : 29732 root       2336 S   /usr/local/bittorrent/bin/btdog /usr/local/bittorrent 29733 root      38820 S   /usr/local/bittorrent/bin/bt
Sep 26 23:26:23 TS-XL038 bittorrent: ps : 29733 root      38820 S   /usr/local/bittorrent/bin/bt
Sep 26 23:26:24 TS-XL038 bittorrent: WaitBtDie is finished.
Sep 26 23:26:25 TS-XL038 linkstation: DWARF : Killing all dwarves
Sep 26 23:26:26 TS-XL038 update_notifications.sh: Not boot process now. cannot register to cron...
Sep 26 23:26:26 TS-XL038 update_notifications.sh: old xml file found. deleting...
Sep 26 23:26:28 TS-XL038 update_notifications.sh: starting f/w cheking process ...
Sep 26 23:26:30 TS-XL038 update_notifications.sh: step1 result=0
Sep 26 23:26:30 TS-XL038 update_notifications.sh: version_is_latest
Sep 26 23:26:30 TS-XL038 update_notifications.sh: deleting from lcd...
Sep 26 23:27:42 TS-XL038 update_notifications.sh: Not boot process now. cannot register to cron...
Sep 26 23:27:43 TS-XL038 update_notifications.sh: old xml file found. deleting...
Sep 26 23:27:44 TS-XL038 update_notifications.sh: starting f/w cheking process ...
Sep 26 23:27:45 TS-XL038 update_notifications.sh: step1 result=0
Sep 26 23:27:45 TS-XL038 update_notifications.sh: version_is_latest
Sep 26 23:27:45 TS-XL038 update_notifications.sh: deleting from lcd...
Sep 26 23:27:51 TS-XL038 twonky: Media Server script is begun. type=start
Sep 26 23:27:51 TS-XL038 twonky: Media Server begins starting. contentbase=/mnt/disk1/share diskinfo=
Sep 26 23:28:00 TS-XL038 twonky: Media Server start was completed. build date=2009-11-09
Sep 27 00:15:01 TS-XL038 S40B_update_notifications.sh: deleting old settings...
Sep 27 00:15:02 TS-XL038 S40B_update_notifications.sh: checking and registering to cron...
Sep 27 00:15:03 TS-XL038 S40B_update_notifications.sh: old xml file found. deleting...
Sep 27 00:15:08 TS-XL038 S40B_update_notifications.sh: starting f/w cheking process ...
Sep 27 00:15:09 TS-XL038 S40B_update_notifications.sh: step1 result=0
Sep 27 00:15:09 TS-XL038 S40B_update_notifications.sh: version_is_latest
Sep 27 00:15:09 TS-XL038 S40B_update_notifications.sh: deleting from lcd...
Sep 27 02:04:04 TS-XL038 kernelmon: cmd=micon_interrupts
发表于 2011-9-27 16:28:16 | 显示全部楼层
第9步开始,还是不行,还是报错,和第8步的报错一样。。。。分区我也分好了的
发表于 2013-12-8 17:36:06 | 显示全部楼层
谢谢了!楼主辛苦!!!
您需要登录后才可以回帖 登录 | 注册

本版积分规则

QQ|小黑屋|手机版|Archiver|GODIY论坛 ( 粤ICP备12089271号

GMT+8, 2018-10-16 21:15 , Processed in 0.224241 second(s), 11 queries , File On.

Powered by Godiy.net

快速回复 返回顶部 返回列表